- USED MAC VALUE OF 2013 MAC POWERBOOK FULL
- USED MAC VALUE OF 2013 MAC POWERBOOK PASSWORD
- USED MAC VALUE OF 2013 MAC POWERBOOK PC
USED MAC VALUE OF 2013 MAC POWERBOOK PASSWORD
The enable password is configured as cisco.ġ7. VLAN1 is configured with a management IP address. The first VTY line is automatically configured to allow remote connections. Which three statements are correct concerning the default configuration of a new switch? (Choose three.) In which mode is a VTP switch operating if it does not allow for the creation of local VLANs but it does accept VLAN updates from other switches in the same domain?ġ6. It prevents loops in a switched network with redundant paths.ġ5. It segments a network into multiple broadcast domains. It restricts broadcast packets to a single VLAN. It propagates VLAN configurations to other switches. What is the purpose of the Spanning Tree algorithm? It will be forwarded out ports Fa0/5, Fa0/10, and Fa0/15.ġ4. It will be forwarded out ports Fa0/5 and Fa0/10. It will be forwarded out port Fa0/5 only. How will switch ST-1 handle Layer 2 broadcast traffic originating from host A on switch ST-C? VTP pruning is enabled in the VTP domain that is shown. What VLANs are allowed across a trunk when the range of allowed VLANs is set to the default value?Īll VLANs except the extended range VLANsġ3. The VLAN1 interface has not be enabled with the no shutdown command.ġ2. The crypto key is not properly configured to generate passwords. S1 does not have a password configured for the vty lines.
S1 does not have login configured on the vty lines. After entering the commands in the exhibit, the administrator receives a “password required, but none set” message when attempting to connect to S1.
USED MAC VALUE OF 2013 MAC POWERBOOK PC
The default gateway is not on the same switch that the PC is.ġ1. The PC and the default gateway have different bandwidth Ethernet ports. The result is that frames are being dropped. The switch traffic is exceeding available frame buffers. The switch port fails to autonegotiate the duplex setting and defaults to half duplex, which causes a duplex mismatch.
USED MAC VALUE OF 2013 MAC POWERBOOK FULL
The switch port is configured for auto duplex and the PC is configured for full duplex. Other PCs on the switch can consistently ping the default gateway. The PC has a ping success rate to the default gateway of less than half the ping attempts. An administrator is troubleshooting a PC on the network which is suffering from slow and intermittent connectivity. Which value determines if a switch becomes the central point of reference in the spanning tree topology?ġ0. Which parameter is used to uniquely identify one wireless network from another?ĩ. Modify the TCP/IP properties of the computer connected to the access point so that it exists on the same network, and then reboot your computer to establish a connection.Ĩ. Physically connect to the access point and then reboot the computer to launch the configuration software.įrom a computer in the same IP subnet as the access point, enter the default IP address of the access point in a web browser. Which method establishes an administrative connection for configuring the Linksys WRT300N wireless access point?Īssociate with the access point and then open a HyperTerminal session with the access point. Interface FastEthernet3/0/0.3 is mapped to the default management VLAN.Īn IP address should be applied to FastEthernet3/0/0 for correct data routing.ħ. The configuration is appropriate for a router-on-a-stick network design.Ī shutdown command has been applied to interface FastEthernet3/0/0.
Interface FastEthernet3/0/0 is subinterfaced.Ī non-proprietary trunking protocol is in use.
Which three options correctly identify information that could be associated with this output?(Choose three.) Which hosts will receive the collision jamming signal?Ħ. Hosts A and B, connected to hub HB1, attempt to transmit a frame at the same time but a collision occurs. One of the router subinterfaces is possibly down.ĥ. No routing protocol is configured on Router1. What is the most likely cause of this problem? A test of the network, however, shows that hosts on each VLAN can only access local resources and not resources on the other VLAN. A network administrator has segmented the network into two VLANs and configured Router1 for inter-VLAN routing. Which Spanning Tree Protocol version is in effect?Ĥ. Which CLI mode allows users to access all device commands, such as those used for configuration, management, and troubleshooting?ģ. To which devices should the IP phones connect?Ģ. A network administrator needs to add IP phones to the network.
0 kommentar(er)
